PV Energy Storage Fuse Ceramic Body
The PV Energy Storage Fuse Ceramic Body is made of high-strength, high-temperature-resistant ceramic materials and is used to protect the high-voltage circuits of new energy vehicles. It has excellent electrical insulation, high voltage resistance, rapid breaking ability and small size. It can quickly cut off the current when the circuit is overloaded or short-circuited to ensure vehicle safety.
- Fast Delievery
- Quality Assurance
- 24/7 Customer Service
Product Introduction
Products description
Our PV Energy Storage Fuse Ceramic Body is produced using high-quality raw materials and advanced production technology under the professional guidance of relevant technical personnel. They are widely used in the new energy automobile industry and play important roles in protecting fuses, insulation, and heat insulation.
products Application
The application of Ceramic Body for EV Fuse is mainly reflected in the protection of high-voltage circuits. With the rapid development of new energy vehicles, especially electric vehicles (EV) and hybrid electric vehicles (HEV), the protection requirements for high-voltage circuits are becoming higher and higher. As an important component of fuses, our product plays an irreplaceable role in this field due to their unique physical and chemical properties.
1. Battery management system
In the battery management system of new energy vehicles, Ceramic Body for EV Fuse are widely used in the connection circuits between battery packs and the output circuits of battery packs. These fuses can quickly cut off the current when the battery pack is overloaded or short-circuited, protecting the battery pack from damage.
2. Motor controller
The motor controller is one of the key components in new energy vehicles. Ceramic for DC Automotive Fuses are used in the input and output circuits of the motor controller to protect the motor controller from current overload and short circuit.
3. High-voltage distribution box
The high-voltage distribution box is an important component for distributing and controlling high-voltage circuits in new energy vehicles. Ceramic for DC Automotive Fuses are used in various circuit branches in the high-voltage distribution box to ensure that the power supply can be quickly cut off when a circuit failure occurs.
packaging & transportation
As a fragile and delicate component, the Ceramic Casing for Fuse Link requires special attention during packaging and transportation to ensure that it arrives at the destination intact. The following are general packaging and transportation methods for ceramic fuse bodies:
1. Choose high-strength packaging materials
Use high-strength cartons or wooden boxes as outer packaging to ensure that it can withstand pressure and vibration during transportation. Use foam plastics, bubble film and other cushioning materials to fill the gaps around the Ceramic Casing for Fuse Link to reduce the impact of vibration and collision on the ceramic body.
2. Customized packaging
For products with special shapes or large sizes, special customized packaging can be designed to ensure that they are stably and safely fixed in the packaging.
3. Moisture and dustproof
Place desiccant in the package to prevent the Ceramic Casing for Fuse Link from getting wet. Use dustproof bags or plastic bags to further protect the ceramic body from dust and stains.
4. Clear labeling
Clearly mark "fragile" and "handle with care" on the package to remind the transportation personnel to pay attention. Provide necessary transportation information and contact information so that you can contact them in time if there is any problem.
We can adjust the specific transportation method according to customer requirements. No matter where you are or what transportation method you require, we will try our best to meet your needs.
Product installation Instructions
The installation method of the Energy Storage Fuse Ceramic Body is as follows:
Inspection and preparation
Before installation, check whether the rated voltage of the fuse is greater than or equal to the rated voltage of the circuit, ensure that the rated breaking capacity of the fuse is greater than the expected short-circuit current in the circuit, and the rated current of the fuse should be less than or equal to the rated current of the fuse holder.
01
Vertical installation
The EV Fuse Ceramic Body should be installed vertically to ensure good contact between the fuse and the contact knife and between the contact knife and the knife holder to prevent the arc from flying to the adjacent live parts.
02
Wiring and fixing
The connecting wires at both ends of the Energy Storage Fuse Ceramic Body should be connected reliably and the screws should be tightened. At the same time, the installation position of the fuse should be convenient for subsequent replacement of the fuse.
03
Precautions
During installation, mechanical damage to the fuse should be avoided, and the temperature of the medium around the fuse should be as consistent as possible with the temperature of the medium around the protected object.
04
contact us
Hot Tags: pv energy storage fuse ceramic body, China, manufacturers, suppliers, factory, Outer Cap For New Energy Electric Vehicle Fuse, NH Fuse Knife, Fuse Copper Cap, Inner Cap With Hole For Automotive Fuse, Fuse Link Contact And End Cap For Auto Car, Contact Fuse Links Assembly
